A $25,000 contribution from ExxonMobil Foundation will aid the students in finalizing their entry in the international Progressive Automotive X PRIZE competition, where they are competing against automakers and innovators to design a viable, clean and super-efficient car that achieves 100 MPG. WHAT: The road to success just got a little smoother for students in Philadelphia Academies, Inc.'s West Philadelphia High School Automotive Academy. Students from West Philadelphia High School's Automotive Academy Nutter, President, Philadelphia Academies, Inc. $25,000 Grant Supports Philadelphia Academies, Inc.'s Program and Student X PRIZE Entry Confirm the proper operation of the vehicle.WEST PHILADELPHIA HIGH SCHOOL'S AUTO ACADEMY RECEIVES GRANT FROM EXXONMOBIL FOUNDATION TO BUILD 100 MPG CAR OF THE FUTURE Replace the Engine Room Main Wire Harness and Junction Block No. Carefully inspect both components for liquid or corrosion in the connector and the junction block (especially the male and female terminals).ĩ. Disconnect connector DD from Junction Block No. Identify connector DD and Junction Block No.1Į. Locate connector DD and Junction Block No. 1 for liquid contamination or corrosion.ī. Inspect connector DD and Junction Block No. Refer to the applicable model year Tacoma Repair Manual for diagnostics for DTC P0705.Ĩ. – If YES – Ground through Stop Lamp Circuit ![]() Does the Neutral Position SW Signal change based on brake pedal input (Stop Lamp Switch on or off) when in Reverse or Drive? Note: Neutral Position SW Signal can show “On” either with the Stop Lamp Switch on or off. Does the Neutral Position SW Signal show “On” at any time when in Reverse or Drive? Review Snapshot after completing the test to confirm if abnormal readings are observed. Press and release the brake pedal when in all gear positions (this can be performed multiple times). Ensure engagement in all gear positions selected.į. Shift between the Park, Reverse, Neutral and Drive positions.Į. Clear all stored DTCs using Techstream.ĭ. Neutral, Reverse and Drive positions is required with the brake pressed and released in all gear positions.Ī. If driving, select an area with no traffic since extensive stopping and shifting between the Park, The following inspection procedure can be performed with the vehicle on the lift or while driving the vehicle. Select the following data parameters for display on the line graphs:ħ. Configure Snapshot as follows: 30-second duration Trigger point at Start (0%)Ĭ. (Refer to the University of Toyota online training class P901C “Techstream InDepth” for information about taking snapshots and graphing snapshots on Techstream.)ī. Hint: Using the Snapshot feature of Techstream makes it easier to review data and confirm duplication of this issue. Prepare the Techstream Data List for performing the testing/duplication procedure in step 7. Using Techstream, clear all stored DTCs and then attempt to duplicate the MIL On DTC P0705.Ħ. Refer to the applicable model year Tacoma repair manual for diagnostics for DTC P0705.ĥ. Are any of the following data list parameters on when the Neutral Position SW Signal is on? If the Neutral Position SW Signal is on, go to step 4.Ĥ. Refer to the applicable model year Tacoma repair manual for diagnostics for DTC P0705. – If the Neutral Position SW Signal is off, this TSB does not apply. Note: In Figure 1, the transmission is not in any gear position on this vehicle. Is the Neutral Position SW Signal value on or off in the freeze-frame data? Print out the freeze-frame data for P0705 to allow easy review of data values. Confirm that DTC P0705 is stored in the freeze-frame data.Ģ. 1 will be required to repair the vehicle.ġ. ![]() If liquid or corrosion is observed in indicated wire harness connector and junction block, replacement of the engine room main wire harness and junction block connector No. Junction block for evidence of liquid or corrosion.Ĥ. If the DTC cannot be duplicated, examine the indicated wire harness electrical connector and Attempt to duplicate the DTC using testing procedure shown in this TSB to confirm TSBģ. Review the DTC P0705 freeze-frame data to determine if this TSB may be applicable.Ģ. ![]() Common symptoms with this DTC can include possible delayed engagement into Reverse or Drive and possible harsh gear engagement when shifting between Park or Neutral into all other gears.įollow the procedure in this TSB to determine if this service bulletin is applicable and to repair the vehicle.ġ.
0 Comments
Leave a Reply. |